Use this property to get or set the curve start parameter.
Cimatron 2024 or later
double StartParam {get; set;}
StartParam:double
|
Return: double |
Parameter―double value of start of parametric range |
|
Input: double |
Parameter―Double value for start of parametric range. |
The input values should be in terms relative to Pi because an arc is being created; That is there should be 0, 3.14, 6.28 and so on between values.
// create Cimatron App Access object
interop.CimAppAccess.AppAccess aAppAccess = new interop.CimAppAccess.AppAccess();
//Get application object from App access
interop.CimatronE.IApplication CimApp = (interop.CimatronE.IApplication)aAppAccess.GetApplication();
// Get active document from application
interop.CimBaseAPI.ICimDocument aDOC = (interop.CimBaseAPI.ICimDocument)CimApp.GetActiveDoc();
if (aDOC != null) // Check if document was found
{
interop.CimMdlrAPI.IModelContainer aModelCont = (interop.CimMdlrAPI.IModelContainer)aDOC;
// Create the Sketcher procedure depended on the type of the active document. For now we take part document
if (aDOC.Type == interop.CimBaseAPI.DocumentEnumType.cmPart)
{
// If active document is part then get the MdlrModel from model container
interop.CimMdlrAPI.MdlrModel aMdlrModel = (interop.CimMdlrAPI.MdlrModel)aModelCont.Model;
//Create sketcher procedure on Modeler Model
interop.CimMdlrAPI.MdSketcher aMdSketcherProcedure =
(interop.CimMdlrAPI.MdSketcher)aMdlrModel.CreateProcedure(interop.CimMdlrAPI.MdProcedureType.cmSketcherProcedure);
// Cast MdSketcher to IMdSketcher to get sketcher object
interop.CimMdlrAPI.IMdSketcher aIMdSketcher = (interop.CimMdlrAPI.IMdSketcher)aMdSketcherProcedure;
interop.CimServicesAPI.ISketcher aISketcher = (interop.CimServicesAPI.ISketcher)aIMdSketcher.Sketcher;
//Create SkEllipse type object
interop.CimServicesAPI.ISkObject aSKEllipseObj = aISketcher.CreateObject(interop.CimServicesAPI.SketchObjectType.cmSketchEllipse);
interop.CimServicesAPI.ISkEllipse aSkEllipse = (interop.CimServicesAPI.ISkEllipse)aSKEllipseObj;
double[] aPoint = new double[2];
aPoint[0] = 0;
aPoint[1] = 0;
aSkEllipse.Center = aPoint;
aPoint[0] = 10;
aPoint[1] = 0;
aSkEllipse.Axis = aPoint;
aSkEllipse.Ratio = 0.8;
aISketcher.AddObject(aSKEllipseObj);
aISketcher.Evaluate();
aMdSketcherProcedure.Execute();
interop.CimServicesAPI.ISkCurve aSKEllipseCurve = (interop.CimServicesAPI.ISkCurve)aSKEllipseObj;
double aStartParam = aSKEllipseCurve.StartParam;
}
}
import clr
#Adding references of required interop dlls
clr.AddReference("interop.CimAppAccess")
clr.AddReference("interop.CimatronE")
clr.AddReference("interop.CimServicesAPI")
clr.AddReference("interop.CimBaseAPI")
clr.AddReference("interop.CimMdlrAPI")
#importing modules from interop dlls
import interop.CimAppAccess
import interop.CimatronE
import interop.CimServicesAPI
import interop.CimBaseAPI
import interop.CimMdlrAPI
#Getting AppAccess Object
aCimAppAccess = interop.CimAppAccess.AppAccess()
#Getting instance of CimatronE Application
aCimApp = None
while (aCimApp == None) :
aCimApp = (interop.CimatronE.IApplication)(aCimAppAccess.GetApplication())
aDocument = (interop.CimatronE.ICimDocument)(aCimApp.GetActiveDoc())
if (aDocument != None) :
if (aDocument.Type == interop.CimatronE.DocumentEnumType.cmPart) :
aModelCont = (interop.CimMdlrAPI.IModelContainer)(aDocument)
#If active document is part then get the MdlrModel from model container
aMdlrModel = (interop.CimMdlrAPI.MdlrModel)(aModelCont.Model)
aMdSketcherProcedure = (interop.CimMdlrAPI.MdSketcher)(aMdlrModel.CreateProcedure(interop.CimMdlrAPI.MdProcedureType.cmSketcherProcedure))
# Cast MdSketcher to IMdSketcher to get sketcher object
aIMdSketcher = (interop.CimMdlrAPI.IMdSketcher)(aMdSketcherProcedure)
aISketcher = (interop.CimServicesAPI.ISketcher)(aIMdSketcher.Sketcher)
#Create SkEllipse type object
aSKEllipseObj= (interop.CimServicesAPI.ISkObject)(aISketcher.CreateObject(interop.CimServicesAPI.SketchObjectType.cmSketchEllipse))
aSkEllipse = (interop.CimServicesAPI.ISkEllipse)(aSKEllipseObj)
from System import Array, Double
aPoint = Array[Double](2)
aPoint[0] = 0
aPoint[1] = 0
aSkEllipse.Center = aPoint
aPoint[0] = 10
aPoint[1] = 0
aSkEllipse.Axis = aPoint
aSkEllipse.Ratio = 0.8
aISketcher.AddObject(aSKEllipseObj)
aISketcher.Evaluate()
aMdSketcherProcedure.Execute()
aSKEllipseCurve = (interop.CimServicesAPI.ISkCurve)(aSKEllipseObj)
aStartParam = aSKEllipseCurve.StartParam